WSS warns SOLAS regulation alone isn’t enough when it comes to gas detection
4 April, 2016: Wilhelmsen Ships Service (WSS) is warning ship operators they must combine vigilance, structure and care with the new SOLAS X1-1/7 - MSC.1/Circ.1477 & MSC.1/Circ.1485 regulations to safeguard crews from the dangers of gas when entering enclosed spaces. Just supplying vessels with one portable four-gas detection unit, as stipulated by the IMO, simply isn’t sufficient, stresses WSS.
The new regulation, coming into force on 1 July 2016, requires all ships engaged in international voyages to have at least one unit capable of detecting the presence of oxygen, flammable gases or vapours, carbon monoxide and hydrogen sulphide. This is an important step forward, the leading global provider of maritime products and services acknowledges, but not the end of the road when it comes to safety.
“The regulation mustn’t be seen in isolation,” comments Andrew Sheriff, Business Manager, Marine Products - Safety Solutions, WSS. “It is sound legislating from the IMO, but it comes with a burden of responsibility for operators. However, this needn’t be an issue if you have the correct knowledge, maintenance structure, and testing procedures in place.”
Most importantly of all, Sheriff notes, the detection units have to be used by individuals entering enclosed spaces or tanks, not forgotten in a drawer. Next, they must be visually inspected regularly, the batteries charged, and the units ‘bump tested’ before use. So, an on-board routine needs to be established whereby the crew satisfy these demands.
“It sounds simple, but it’s very serious,” he stresses. “Also, don’t forget the batteries and sensor will need replacing after 30 months to be on the safe side, or when their runtime drops below that of the shortest on-board shift. A failure to do this can cause some units to ‘forget’ they are equipped with a dual range sensor for combustible gasses.
“The unit’s audible and visual alarms must also be checked regularly and must be free of grime and dirt - which can obstruct them – while the housing of the detector should be free of cracks. If it isn’t water can corrode the inner circuit boards and, if the detector isn’t ‘gas tight’, it can actually, in the worst case scenarios, cause explosions.”
Simple visual and functional checks suffice in these respects, but not in all. The sensors that detect the gas are sensitive to contamination, so must be stored carefully to protect them. Testing them with a lighter, as some crewmembers do, is a definite no.
“This is too high a concentration of gas and basically destroys the sensor’s ability immediately.”
With so many potential risks to detector integrity crews should be trained to perform ‘bump’ tests. This consists of exposing sensors to a challenge gas at a sufficient concentration to activate a unit’s alarms at its lower level settings. It proves it works, but not how accurate it is. This is when, according to Sheriff, it may be time to call in the professionals:
“In order to measure the performance of the sensors a ‘calibration check’, using a traceable source test gas at a set concentration, must be done. This involves measuring the sensor’s responses according to the detector manufacturer’s acceptable limits, which can vary from brand to brand. It is much more difficult to perform on board than the other checks.
“Well informed, regimented crew members will be able to safely use and check the basic robustness and functions of a four-gas detection unit. However, personally speaking, if I was in a confined space on a vessel and my life depended on this piece of equipment, I’d want it calibrated by a professional.”
WSS supplies a range of advanced Unitor gas detection units, such as the Unitor Gas Pro, with complete maintenance packages delivered by skilled technicians, thus ensuring optimal standards of operation. This solution dispenses with the need for exchanging units at service centres, or investing in on-vessel calibration kits. WSS’ service engineers can efficiently re-certificate, calibrate and inspect gas detectors on board when visiting to test or inspect other equipment.
All WSS units have been tested with stringent drop and moisture tests, giving them an increased operational lifespan. The Unitor T4 unit is also supplied with an external filter as standard for increased protection.
“This is an essential device, but it needs to be looked after properly to work,” concludes Sheriff. “The regulations must be backed up by the right mix of everyday care and professional maintenance. By doing so this new regulation will really fulfil its potential to safeguard assets, operations and, most importantly of all, lives.”
For further information, contact:
Ole Jakob Ytterdal
Head of Communications
Wilhelmsen Ships Service
Tel: +47 67 58 40 00
Mobile: +47 97 08 83 62
Wilhelmsen Ships Service is part of Wilhelmsen Maritime Services, a Wilh. Wilhelmsen group company. It has the world’s largest maritime services network, with 4,500 marine professionals servicing 2,200 ports in 125 countries. Wilhelmsen Ships Service supplies safety products and services, Unitor products, Unicool refrigerants, Unitor and Nalfleet marine chemicals, maritime logistics and ships agency to the maritime industry. Last year the company made product deliveries to 25,000 vessels and handled 70,000 port calls. For more information, see wilhelmsen.com/shipsservice