DAYCO TECHNICAL TIPS
![](https://mb.cision.com/Public/283/9247311/b2ecbef35052c314_800x800ar.png)
How To Detect A Worn Multi-Rib Belt
Dayco recommends that workshops endeavouring to provide the motorist with a high standard of service and repair must make sure that they regularly check the condition of all multi-rib auxiliary belts and replace them when the signs of wear become visible.
However, what are the signs and how can the degree of wear be judged accurately to ensure that a worn belt is replaced, but a serviceable belt is not replaced unnecessarily?
Historically, multi-rib belts were made from neoprene compound, had a service life of between 50,000 to 80,000 miles and the signs of wear were generally obvious in the form of cracking, chunking (small sections of the belt break off), glazing or splitting. Today’s belts in contrast are made of extended-life rubber compound (EPDM), have a service life of around 100,000 miles and the wear signs are more difficult to detect as these belts tend to wear through material loss, in the same way as a tyre.
As a result, the ‘V’ profiles of the ribs on the belt begin to wear down and start to resemble a ‘U’ and not a ‘V’. As the profile changes, the contact area of the belt on the pulley is reduced and the efficiency of the belt drops, which can lead to slippage and affect the performance of the belt, as well make it very noisy.
In order for workshops to quickly and accurately measure the wear of these belts, Dayco has produced an easy-to-use tool that makes the process extremely straightforward. The Dayco ‘a-WEAR-ness gauge’ is a small but robust plastic tool that allows the technician to perform three visual checks that will clearly reveal the condition of the belt.
First the profile of the ribs can be measured using the ‘comb’ end of the tool, which when held against the ribs will show whether there is any side clearance between the teeth of the ‘comb’ and the side of the ribs. A new, or still serviceable, belt will show no side clearance, but on a worn belt, the base of the teeth will bottom out on the top to the ribs and reveal a gap between the sides of the ribs and the teeth of the tool. (Fig B & C)
The second check will show the wear on the ribs themselves. An indicator ‘bar’ on the opposite end of the tool to the comb, will sit above the tops of the ribs when placed lengthways along the groove on a new belt, but sit below the top of the ribs along the groove of a worn belt. This shows that material has worn away and the gap between the ribs has increased. (Fig A)
The final check for cracks allows the technician to view the ribs through a 25mm square ‘window’. If four or more cracks are visible through the window, then the belt must be replaced before failure occurs. (Fig D)
The condition of the auxiliary belt should not be overlooked, particularly as they tend to drive more components on a modern vehicle and the environment in which they operate is very hot and can contain harmful contaminates. Although auxiliary belt failure is not usually as catastrophic as the failure of a timing belt, it will nonetheless stop the vehicle and necessitate its recovery.
Therefore Dayco also recommends that the regular inspection of all drive belts be mandatory after the vehicle has reached 75,000 miles and that whenever the timing belt is replaced, the auxiliary belt is careful checked and if necessary replaced alongside the fitting of a new timing belt kit.
The Dayco aWearness gauge is available alongside its full range of OEM quality power transmission products from Universal Automotive in the UK on: 01562 512512 and Team PR Reilly in ROI on: +353 (0) 1-832 0006 or for further information please email: info.uk@dayco.com or visit: www.dayco.com
ENDS
For further information relating to this press material, please contact Steve Coombes on: 01753 785957 or e-mail: steve@chicanemarketing.co.uk
Chicane is an established PR agency with a particular specialism in the automotive aftermarket and the motorsport industry.
Prix De la Communication and Barrington Needham Trophy award winners.