NFET pre-driver with EEPROM configurability from Melexis reduces footprint & increases operating range for 3 phase BLDC motor control
Tessenderlo, Belgium, August 23, 2012 – 3 phase brush-less DC (BLDC) motor applications bring higher efficiency and improved performance to electromechanical actuation in automotive systems like pumps, power steering, engine cooling fans and fast positioning drivetrain actuators. Melexis latest pre-driver IC, the MLX83203, deploys EEPROM memory and combined bootstrap and charge pump blocks. Whereas traditional BLDC pre-driver ICs require complex, large packages with many external components, the MLX83203 delivers a flexible pre-driver solution in a space saving, standard, QFN32 5x5 package.
The IC drives six 250 nC NFETS up to 25k Hz, while keeping 10 V gate voltage down to 7V battery voltage. In line with the needs for such fail safe torque control applications, the MLX83203 features extensive diagnostics as well as a high speed, low noise amplifier. Rather than configuring the pre-driver by applying external resistors, 6 bytes of on-chip EEPROM offer wide-ranging configuration options while minimizing pin count.
The low self heating and small pin count means that the MLX83203 presents the smallest footprint for comparable 3 phase pre-drivers on the market. The benefit is a smaller finished size, fewer components and more flexibility for design re-use. Additional family members are planned for release in the coming months. The MLX83203 will be released for operation up to 150 °C and qualification to 175 °C is planned for the near future. Further members of this product family will support medium current capability and DC motor control.
The wide operating voltage range from 4.5 V to 28 V, plus bootstrap topology complemented with a charge pump stage, allow operating of the power stage via standard level NFETs without loss of performance during stop/start conditions, as well as enabling control even during engine cranking. The charge pump can be configured for applying a high side NFET reverse polarity protection. In sleep mode the IC consumes less than 30 µA standby current. A 10 MHz gain bandwidth product (GBW) delivers shunt amplifier settling times of less than 1µs for fast current feedback. Its gain can be programmed in a wide range from 8 up to 48, and the input range can be configured from fully symmetric to full scale.The power stage (VDS, VGS) as well as all input voltages are monitored with comparators to offer maximum system level diagnostics. A high speed serial interface provides detailed diagnostics feedback to the microcontroller.
Thanks to its wide configurability and high operating temperature, the pre-driver family, in addition to power steering systems, can be applied to engine cooling fans, blowers, water/oil/fuel pumps, drive train position actuators and wipers. The family will include 3 phase BLDC predrivers, as well as 2 phase predrivers for brushed DC applications. Package options include wettable flanks QFN, TQFP and TSSOP, all with exposed pad.
Production will be released in Q1 2013, and final samples are available through the standard Melexis sales channels.
For more information please visit: www.melexis.com/MLX83203
About Melexis
Melexis Microelectronic Integrated Systems N.V. (Euronext Brussels:MELE) imagines, creates and delivers innovative mixed signal integrated circuits. Melexis ICs are driving green solutions that enable our customers to bring more energy efficient automotive systems to market. Melexis product portfolio addresses 4 classes of ICs; Sensor, Optoelectronic, Wireless and Actuators. Sensors include magnetic, MEMs, and sensor interface ICs. Optoelectronic products encompass linear arrays, single point sensors, infrared thermometers and CMOS wide dynamic range and night vision cameras. Wireless ICs focus on RKE, TPMS, ISM band applications, NFC, RFID reader and smart tag solutions. Actuator ICs cover LIN and CAN bus networking ICs and advanced BLDC motor driver technology. Melexis is proud of its participation toward reducing the human race's global environmental footprint.
For more information visit www.melexis.com
Contact Melexis
Applications & Marketing Sales Leads
Rik Moens Brenda Vanderheyden
Melexis Melexis
Transportstraat 1. Transportstraat 1.
3980 Tessenderlo 3980 Tessenderlo
Belgium Belgium
Tel: +32 13 670 795 Tel: +32 13 670 495
Fax: +32 13 672 134 Fax: +32 13 672 134
rmo@melexis.com brv@melexis.com
Issued by:
Mike Green
Pinnacle Marketing Communications Ltd
Tel: +44 208 4296 543
E-mail: m.green@pinnaclemarcom.com
Web: www.pinnacle-marketing.com
Tags:
