Post-tension is a niche but typical sector in the construction industry
Post-tensioned structures are widely used around the world. However, in Finland, there are only a few companies that carry out these contracts. YIT's post-tension work unit even develops their own tools.
In short, post-tensioning is structural reinforcement. The basic idea is the same as taking a stack of books and trying to keep them between your hands; they must be squeezed hard with both hands so that they don’t fall to the floor. The harder you squeeze, the more weight you can put on top of the books.
In post-tensioning, instead of books a concrete structure is compressed. Before pouring the concrete, flexible steel wires are placed in a curved shape inside the formwork, the shape of which has been calculated by the structural designer. After about a week, when the concrete has dried, the cables are tightened using a hydraulic jack, after which the structure can be loaded as planned. One end of the wire is wedged tightly with an anchor piece to prevent it from slipping off the structure, and the other end is operated. Once the desired force has been applied to the wire, the wires are locked in place with a wedge. This allows the structure to rise slightly as an arc, sometimes even noticeable to the naked eye, but always a maximum of just a few centimetres. Then, as the structure is loaded with the planned loads, it straightens to an even structure.
Post-tensioned structures are used everywhere, including parking halls, bridges, various commercial premises and apartment buildings, rail traffic, wind power and hydropower plants, nuclear power plants, water towers, water treatment plants, ports and refineries. In our built environment, such structures are everywhere.
Safety is the core of post-tension work
“Post-tensioned structures are widely used around the world. However, in Finland, there are only a few companies that carry out these contracts. This is a niche sector in the construction industry, but it is a typical part of it. We mainly work in building construction, but we also make bridge structures and various earth and rock anchors for wind turbines, for example,” says Mikko Toivonen, the head of the post-tension work unit at YIT.
His team also develops their own tools, most often guided by occupational safety as safety always comes first in the construction industry. In special contracting, such as post-tension work, special attention is paid to this. Those who work in the unit consider it their duty to see that those who work with them can work safely and are aware of the risks involved in the work.
“As this work deals with substantial forces when operating with hydraulic jacks, we repeat the occupational safety mantra at every step so that those with us on the site have internalised it. Although this is a routine for us, it may not be for other people working on the site,” says Toivonen.
Occupational safety can be compared to air traffic. At all stages, from negotiations to actual work, occupational safety and related plans are reviewed. All tools are also inspected before each task and when post-tension tasks are underway, the safety limits can be several metres.
“There is an area of 15 metres behind the jacks where you are not allowed to stay during work so that, in the unlikely event that the wire breaks, no one is standing in the impact area. The hydraulic hoses have very high pressure, so when they are disconnected, they can cause damage in the vicinity. The instruments are inspected again and again to avoid any damage."
Patience, organisational skills and the ability to prioritise
Learning the ropes in post-tension work takes a long time, an average of two and a half years. Tasks are not learned at school but on construction sites, from more experienced experts.
Working in a unit requires patience, organisational skills and the ability to prioritise one’s own work tasks independently.
In addition to Group’s own construction sites, the unit also provides services to other construction companies. In addition, Toivonen also does design planning and design supervision, leads a course on exceptionally complex concrete structures for foremen and gives lectures on the consideration of site implementation in the design of post-tensioned structures for structural designers.
“I think it’s important to share the information one has accumulated over the years. I’m happy to talk about the services of our unit. It’s in my job description to help start the process of designing post-tensioned structures across segment boundaries and to optimise structural solutions. I’m also happy to speak about the possibilities of a post-tension alternative for a project when choosing a framework solution. Feel free to stay in touch!”
For further information, please contact:
Mikko Toivonen, head of the post-tension work unit , YIT Corporation, tel. +358 (0) 50 564 6997, mikko.toivonen@yit.fi
Pirita Tiusanen, Communications Manager, YIT Corporation, tel. +358 (0)44 240 9822, pirita.tiusanen@yit.fi
We develop and build apartments and living services, business premises and entire areas. We are also specialised in demanding infrastructure construction. Together with our customers, our nearly 8,000 professionals are creating more functional, attractive and sustainable cities and environments. We operate in 10 countries: Finland, Russia, Sweden, Norway, the Baltic countries, the Czech Republic, Slovakia and Poland. Our revenue in 2019 was approximately EUR 3.4 billion. YIT Corporation's share is listed on Nasdaq Helsinki Oy. www.yitgroup.com
Tags:
